FED365EBC Frigidaire Range - Instructions

1. Remove all four control knobs.
2. Unscrew all four plastic "nuts" found under each knob holding front
panel to stove.
3. Lift front panel off.
4. Removed all Phillips screws holding metal shield to which control
switches are fastened.
5. Lift entire assembly up.
6. Remove two screws holding bad switch to metal shield.
7. BEFORE REMOVING ANY WIRES LABEL EACH WIRE
ACCORDING TO CODE EMBOSSED ON BACK OF BAD
SWITCH. These will be H1, H2, L1, L2 and P. They are not in
the same place on the new switch as they are on the old one.
The reason for labeling is that in case you make a mistake you
have this back-up to go by. Also to double check your finished
job.If just one wire is connected to the
wrong terminal a disaster will happen.
8. Remove each wire, one at a time from the old switch and connect
it to the correct terminal on the new switch as indicated by the
codes on the back of the new switch. When done double check
to be certain the labels on each wire match the code for the
connected terminal.
9. Slide furnished bushing onto the new switch.
10. Insert new switch through the back of the metal shield and attach
with the supplied screws. The old screws were too short in my
case so be certain to use the ones supplied with the new switch.
11. Re-attach the shield assembly to the stove.
12. Install the front panel back over the switch stems.
13. Secure the front panel with the four plastic nuts.
14. Install the control knobs.
15. Test the new switch.

Pulled out stove, took side panel off on switch side of oven, unplugged old switch, pulled the old switch out the front of the oven, put in new switch and plugged it in. Then put oven back together and pushed it back into space. (Make sure to turn oven off at breaker box before you make repair) you could easily get shocked if you don’t.

Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

removed replaced in lest than five minute

Turned off breaker to range then removed all element control knobs. Unscrewed retaining collars I suppose is a good word removed panel. Then removed bad switch installed removed one wire at a time and placed on new switch in proper places. Reassembled in reverse order turned breaker back on worked perfect.

Drawings on web site somewhat hard to read, resulting in more
disassembly than actually necessary. Turns out, simply removing the
threaded plastic securing rings around the bases of the controls frees
up the faceplate, and allows access to the phillips screws that hold down
the bracket. Then it's a simple matter to replace the control unit by
swapping out the leads one at a time from old to new. Be careful when
re-attaching those plastic securing rings, they can cross-thread pretty
easily.

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).

I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface
My son can now clean his dirty oven

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you