Models > FES367BCB > Instructions

FES367BCB Frigidaire Range - Instructions

Jump to:

All Instructions for the FES367BCB

Customer:: Sue from Lampasas, TX
Parts Used:: 5304409888
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sharon from Foley, AL
Parts Used:: 5304524341, 316538904
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: James from Milford, IN
Parts Used:: 318394803
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Stove door switch was broken

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Was this instruction helpful to you?

Customer:: Constantine from Vero Beach, FL
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

lower oven element burned up

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Was this instruction helpful to you?

Customer:: WILLIAM from RIDGE, NY
Parts Used:: 318254699
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

end caps that hold the stove at proper depth and support control panels broken

repair was pretty simple. i pulled stove out from cabinet and unplugged it. Then i removed the screws that hold the face panel in place and gently slid out panel as far as i could without damaging wires. i had to remove the small switches that control the two two size burners as well as one thermostat on the right side so i can access the nuts holding the plastic end caps in place. i diagramed the color coded wires so i didnt mix them up.took off the old end caps replaced with new caps and put back together.. took about a half hour as this was my first time inside the guts of this stove.. stove is baack in place and as good as new again.

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper temperature when baking.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Was this instruction helpful to you?

Customer:: Michael from Orange, TX
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

broke element.

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper oven heating.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Was this instruction helpful to you?

Customer:: Vista M. from Northport, AL
Parts Used:: 318293827
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Unable to control surface burner temperature

Pull range unit from wall. Disconnect power cord. Remove back panel on range(10 Phillips head screws). Pull knob from surface burner switch and remove two screws. Remove and re-connect wires from switch by number on switch. Replace switch and back range panel. Re-connect power cord and re-position range to original spot.

Was this instruction helpful to you?

Customer:: Russell from North Smithfield, RI
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Oven did not work since bake element did not warm up.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Was this instruction helpful to you?

Customer:: Robert from Glasgow, MT
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Was this instruction helpful to you?

Customer:: Jeffery from Union Point, GA
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Was this instruction helpful to you?

Customer:: Gerald from Artesia, NM
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Coil melted in half.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Was this instruction helpful to you?

Customer:: Kathleen from Lawrenceville, GA
Parts Used:: 318293820
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner on top occasionally went to high heat though it was set at low

Replaced the switch...removed old switch and transferred the wires one at a time to the new switch. Seems to working fine..

Was this instruction helpful to you?

Customer:: Jack from Hedgesville, WV
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Heating element burned out

Took screws loose, unplugged old one plugged in new one put screws back

Was this instruction helpful to you?

All Instructions for the FES367BCB