CFEF372EC4 Frigidaire Range - Instructions

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

pulled door off took door apart replaced hinge

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

Husband/wife effort. We located our manual for removing the door and followed instructions. (It's probably online as well.) With the door off, we removed the screws on the side with the defective hinge, took out the old hinge and put in the new one. In trying to replace the door, we couldn't get the lock (upside-down u-shaped piece on the hinge) to rotate over the hinge lever hook on the new hinge. It looked slightly different than the other side (had a bit more hook on it that was in the way). PartSelect sent a new hinge in case the other was defective. (The first arrived in 2 days; the second in 3. No extra charge. Very pleased with the service!) Same trouble. So we filed off the tip of the hook and were able to move the lock in place and put the door back on. The door is not heavy anymore, but doesn't pull in tightly at the top. We thought about taking it off again and trying to position the new hinge a little better to see if it will fit perfectly (it slants down a little compared to the other side.) But it's not so loose at the top that the oven light comes on, so it's usable the way it is. And it looks good, so we're leaving it.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

Found a YouTube video similar to the required repair. Took door off, disassembled the door, replaced the right hinge-spring assy, reassembled. Worked great. High quality replacement part from Part Select that was made in the USA.

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

I went to you-tube and found a video that told me how to remove and expose the hinge. That was all I needed. One stubborn screw was all the problem I had and it was replaced. Thank you for saving me lots of money!! It's working great and I would buy from Part Select again!

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Removed outer glass first ,then worked my way thru to inner glass..

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.