FEF366CGSB Frigidaire Range - Instructions

First I unplugged the the stove. I then unscrewed the two screw holding the element. Because I had read the other repair reports on the site, I was very careful in pulling the element out so I wouldn't lose the wires in the rear of the stove.
Once out, I held them with the pliers and gently pulled the element until it was loose. Plugged in the new element screwed it back in and plugged in the oven. Worked like a charm. By the way the part arrived the day after ordering it!!!! This is a great site.

Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim

Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.

First I removed 2 screws that held the stove top in place. Raised the stove top and support it. Then, I removed the hold down spring for the burner and removed three wires from the old burner. I found that the connector on the white wire was spread open too much so I crimped it closed for a better fit on the terminal. I reattached the three wires, put the hold down spring back in place, lowered the stove top and installed the 2 screws. JOB DONE

Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances going as long as possible.

Pulled out the stove, removed the screws that held on the back panel, took out the 2 screws that held in the element and disconnected the wires and put the new one in. I put the screw back in and was finished!

The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.

order pcs fit perfect.

I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.