FGF366CCD Frigidaire Range - Instructions

I removed the back panel, removed the 4 screws holding in the clock, unplugged the wiring harness plug. I then had to remove the display screen which was glued onto the main clock piece. To accomplish this without tearing it, I used a hairdryer to soften the adhesive just enough to peal it off. Luckily, enough glue remained that I could then stick it onto the new clock. I then plugged in the wiring harness and reinstalled the clock and rear panel.

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

Checked internet for possible reasons why oven would not heat.

Found Partselect.com website. Searched and found that ignitor was probably the problem.

Put in my oven model number and found ignitor. Ordered ignitor.

When new ignitor came in I simply removed two screws that held old ignitor and disconnected two wire.
Put new ignitor on, replaced screws and wires.

Repair done and oven works great.

Pull off the old knob, and slide the new knob into place. Less than 10 seconds for each knob.

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.

Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.

PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.

On to the actual repair:

I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.

I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.

Oven fired right up!

Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)

Thanks, PartSelect!

Removed grates and range cover, unscrewed all sheet metal screws and removed cover plate. Disconnect electrical connector and then removed old ignitor/orifice ass and replaced it with the new one. Replaced all screws in cover plate and then reattached range cover and grates. Turned on the gas and it lit after a few sparks took place.

Slide out the old; slide in the new!

I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.

Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the connector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Simple: remove the element by hand and replace new one.

I can't believe how quickly I received my new part -literally next day.

I compaed price at different sites and partselect .com was 30% cheaper for the same item. I received the part in 2 days by fed-ex.
Doing the job was real easy.Just pull the old knob out and put the new one in.

removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw}
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model