FGF328FSB Frigidaire Range - Instructions

It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.

It helps to remove the bottom drawer completely to gain easier access.

First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.

Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.

New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS

Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!

I followed the instructions given pretty much, however none of them mentioned one important point.To remove the cover plate, do NOT try to pry it away from the unit. It will crack. Fortunately I caught it in time.I then started in another corner by inserting a razor knife between the face plate and unit and sliding it around all four sides. There was enough goo left on the plate to enable me to affix it to the new unit.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Disconnected power cord to range
Removed the cover over the flame guard
Removed the Flame guard
Pulled out broiler drawer
Unscrewed the cover and disconnected the white plastic connector to the ignitor wires
Un crewed the two small screws to the ignitor and removed the old ignitor
Cut the two wires from the old ignitor
Connected the new ignitor to the wires on the white connector
Installed the new ignitor
Reassembled parts dsassembled
Plugged in power cord

Works

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down and I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

See other posts.... they have the correct repair procedures.

HIGHLY RECOMMEND removing the bottom drawer to access the space where splice will be made between new igniter wires and existing wires. This step is recommended in previous posts. I wasted a lot of time taking out unnecessary stuff in the oven compartment before I realized that the drawer compartment provided easy access for repair. Story of my life on just about all repairs.

Remove bottom plates and deflector from oven, remove old igniter. Remove bottom drawer and panel to expose wiring. Cut wires, used supplied wire nuts to splice. The time consuming part of this job was having to clean all the parts before reassembly, and having to extract screws that were rusted into place due to heat and spillage. One of the igniter screws was stripped, and was very difficult to remove. The first part in your "probably cause" list was the right one! Thanks for the good service, and a useful website!

Screw the handle, that it...

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

6 screws to remove upper back panel, 4 screws to remove control. Unplug wire harness. Carefully remove adhesive backed front display cover & press to new control, & reverse process to reinstall. Exact original replacement part, quick delivery! replacement