FEFBMZ96FCB Frigidaire Range - Instructions

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.

So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

Removed back, identified faulty parts and next aired replacements. Easy job with screw gun and needle nose.

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Took bolts out of back of oven ,pull out element had take electric clips off .Then I just plugged in the element ,push in and tighten up bolts. Turn oven on IT Works Yea!!!!!

This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.