FGF379WXBCA Frigidaire Range - Instructions

Very easy just had to pull the wire up that holds it secure.

This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.

Disconnected power cord to range
Removed the cover over the flame guard
Removed the Flame guard
Pulled out broiler drawer
Unscrewed the cover and disconnected the white plastic connector to the ignitor wires
Un crewed the two small screws to the ignitor and removed the old ignitor
Cut the two wires from the old ignitor
Connected the new ignitor to the wires on the white connector
Installed the new ignitor
Reassembled parts dsassembled
Plugged in power cord

Works

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

See other posts.... they have the correct repair procedures.

HIGHLY RECOMMEND removing the bottom drawer to access the space where splice will be made between new igniter wires and existing wires. This step is recommended in previous posts. I wasted a lot of time taking out unnecessary stuff in the oven compartment before I realized that the drawer compartment provided easy access for repair. Story of my life on just about all repairs.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Relatively easy to install once you get to the item.

Removed the front panel, top panel, original clock timer.
(15+ screws)
The leads were stuck and had to be pried out with a knife. As I removed one lead I inserted it into the same on the new panel.((eight leads various colors.)
One connector to remove and insert into new panel.
Done!!!! It worked!!! EXCEPT;
After putting it all together I discovered that the push buttons were not included with the unit. I had to pry out the old ones and reuse them on the new timer.

If it hadn't been for the push buttons the whole job would have taken about an hour.

Oh, just a reminder, turn off the eletricity. I forgot to and lit up a bit.

Remove bottom plates and deflector from oven, remove old igniter. Remove bottom drawer and panel to expose wiring. Cut wires, used supplied wire nuts to splice. The time consuming part of this job was having to clean all the parts before reassembly, and having to extract screws that were rusted into place due to heat and spillage. One of the igniter screws was stripped, and was very difficult to remove. The first part in your "probably cause" list was the right one! Thanks for the good service, and a useful website!

I had to remove the whole back of the stove in order to gain access to the timer which is housed on the top console of the stove. There was 8 different leads and a wiring harness to keep track of. I had a friend help and after a good two hours we finally got it. I was never able to remove the top console so had to resort to a bit of prying to gain access to all of the screws. The manufacture did not make this an easy project. The part was rather expensive but with some thought and patients I now have a clock timer with a bright LED display with only one screw left over.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Having already removed the old igniter , replaced it with new.

I followed Ryan's instructions and had no problem following them. HOWEVER, I ENCOUNTERED A MAJOR PROBLEM when I put it all back together: the control buttons wouldn't work. I took it apart again and examined the old one, which had plastic pins in the holes which the buttons were supposed to push. The new part didn't have the pins. I wanted to remove the pins from the old part and put them in the new one. This was difficult, and I broke the first one when I removed it. (I ended up super-gluing it together successfully.) In order to remove the other pins, I pried and pinched with needle-nose pliers to remove the plastic collar around the pin, then the pin came out easily and could be inserted in the new part, pushing hard until it clicked in place. Then when I put everything together it worked fine.

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.