CFEF372ES5 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Hedgesville, WV
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out
Took screws loose, unplugged old one plugged in new one put screws back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Olathe, KS
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven handle brittle and broke in two.when I dropped a pot on it.
It was easy once I got screws that work.Old screws and handle had machine screws that held handle on.Order screws with handle so you can install immediately...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glasgow, MT
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Union Point, GA
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out on my oven
Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Artesia, NM
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Coil melted in half.
First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Reno, NV
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lake Mary, FL
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Really easy to replace handle. However, because the new handle does not have the metal inserts to receive the attaching screws (!appearently a bit cheaper to make!), I am concerned that it will not last as long. I could find no reference to new attaching screws so used the old ones...hope it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorenza from Rowlesburg, WV
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Improper temperature when baking.
Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorenza from Rowlesburg, WV
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Improper oven heating.
1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARGARET from MILFORD, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner would not heat up
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from San Saba, TX
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom element in oven not heating.
We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.
Was this instruction helpful to you?
Thank you for voting!
Oven would not reach temperature
Husband made install in very short time. Nice to have them back in operation.
Was this instruction helpful to you?
Thank you for voting!