FEF303CWC Frigidaire Range - Instructions

Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

raise top of stove unplug burner plug in new one done

I unplugged the stove from the power plug in the wall. There are two screws at the back of the oven to hold the element in place. I removed the two screws. There are wire clamp inserts that attach to the element. Once the element was loose from the back wall of the oven, I gently pulled out the wire clamps. Removed the element. I laid the new element in the bottom of the oven and gently pushed the wire clamps into the new element. Re-attached the screws and put the power back into the wall and I was done. Easy, easy, easy. As for the drip pans, I pulled the element from the plug just under the stove top, cleaned the element and replaced the old drip pans with the new. Slid the element back into the plug and I was done.

All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.

Thanks, PartSelect

Plug the new element into the space on stove

really easy unscrew the element from the back of the oven unclip remove old one slide clip on the new one and screw back to back of oven. Took 10 minutes or less

Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done

Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.