FGF367BGWE Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- June from Mt. Vernon, AL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rusty worn out oven racks
Removed the old oven racks and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarence from Colorado Springs, CO
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The front drawer clip was broken
I took the drawer completely out and installed the new clip just like the video instructed. All went very well with no problems. The drawer works like new. I am glad that I was able to find the part on this site. Thank you so much. I will be using this site in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Dunedin, FL
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Front Drawer Glide
Snapped in the new replacement part and intalled stove drawer in less then two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemarie from Chalfont, PA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front drawer gluide broke
Ordered part which arrived in 2 days, yeah!! Installation was really simple, took less than a minute. The online instructions/ video were very helpful! Excellent site to order parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from El Paso, TX
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Front drawer guides broke
Popped out the old...snapped in the new. All of about 5 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alberta from East Glenville, NY
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer glide snapped in half
Ordered the replacement glide, received pretty quickly! : ) Snapped the broken part out with screw driver and popped the replacement glide in with my thumb! 1,2,3.... Pretty Happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Virginia Beach, VA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Front drawer broken.
Followed instructions shown in video on line.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Lakewood, OH
- Parts Used:
- 5304497424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas Oven Overheating
Removed cover on back of range (four screws held it in place), removed screws holding the oven sensor in place, pulled out oven sensor and disconnected the snap-like connection, tested with ohm reader (was below 1000 and 1100), ordered new part (came next day), inserted the sensor, screwed it back in, snapped the connectors together, replaced cover on back of stove. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Fenton, MI
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My glide to the range drawer broke off.
I just pulled out the drawer, and inserted the replace part into the little hole that the old one was. It works great.Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Manasquan, NJ
- Parts Used:
- 316495901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Leavenworth, KS
- Parts Used:
- 316101514
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clock overlay buttons where scratched away
once I figured out how to get to it it was fairly easy, make sure you carefully disconnect the indicators lights for the speed bake and surface before you try to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Brooklyn, NY
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Oven ignitor did not turn spark for the oven to turn on and heat up.
I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from lexington park, MD
- Parts Used:
- 5303208499, 5303935068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven or boiler not lighting
removed gas safty and igniter .replaced 4 screws and 3/8 wrench. make sure you turn the gas off frist.after repairs are done make sure there are no leaks at fittings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ubly, MI
- Parts Used:
- 316101514
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
clock overlay was wore out and cracked
The repair went really well, from the time I talked with the rep on the phone it was twenty four hours later and the part was in my hands. Great service! Because it was just the clock overlay all it took was a screwdriver to take the panel off and peel the old one off a nd stick the new one on. I will use part select again in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Weidman, MI
- Parts Used:
- 316011200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Igniter electrode broke
The three bolts that held the burner busted off when tring to loosen. I drilled out the old studs and replaced with self tapping screws.
Was this instruction helpful to you?
Thank you for voting!