GEF365CHSA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Right rear burner not working properly
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dineshbhai from Rincon HWY21, GA
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
N/A
I had open back cover and remove the switch than replace new switch. Makesure cable conection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- junius from WICOMICO, VA
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Burner switch work sometime.
I follow the video on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from KEENE, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from FRUITHURST, AL
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from American Fort, UT
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner switch had gone bad.
I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Coeur d'Alene, ID
- Parts Used:
- 318228310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lens was broken
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- German from Houston, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I could can not control the burner
was easy open the back side of the range and change the part, the only issue was the wire I used the diagram
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW HYDE PARK, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The switch wasn't working on all the different settings.
first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Edina, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large front burner would not come on under setting of "3"
Replaced infinite control very easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MOUNT VERNON, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners constantly overheating, and inconsistent heating.
With the stove pulled out and unplugged, There are 4 square head screws to pull a metal plate off the back of the range. Once that is off, the infinite switches are in line and can be removed with a philips head screw driver/bit. I placed each wire onto the new switch as I removed them from the old, to avoid any confusion. The entire repair took less than 10 minutes. Incredibly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from SANDY, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burner switch failure
Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sajeed from GRANADA HILLS, CA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The burner on the top left (closest to front) would not turn off.
1 - Turn off the power from the panel. 2 - Unplugged the range from outlet. 3 - Unscrewed the black hex screws from the rear panel. 4 - Took a pic of the bad infinite burner switch to ensure the correct wires would connect to the new switch. 5 - Removed knob and unscrewed switch, then replaced with new switch. Matched all of the wires to like, L1, L2, P, H1 and H2. If any wires do not exist for your switch, it is ok because not all ranges use all wires.
Was this instruction helpful to you?
Thank you for voting!