CFEF257CS3 Frigidaire Range - Instructions

Very simply following the online video instructions.

Figured out that light and door switch started the convection fan on when door is closed. Found the switch defective. Found exploded view online of switch in oven. Had to figure out that the range top needed to be removed to access the switch from inside the top part of oven. Unscrewed at least (6) screws to free up the range top. Squeezed the inside switch clips to allow switch to be pulled out from outside of oven. Disconnected electrical receptacle and plugged into new switch. Pushed in new switch til it snapped into place. Reinstalled range top.

Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!

Reviewed the online repair video a few times then got started. Although only two were bad, I replaced all four terminal blocks. I removed the range top instead of using the built in kick stands. this left me much more room to work and I was able to clean the top of the range really well before getting started. Wires for the back terminals where short and a little difficult to use after cutting off the old terminal blocks. The terminal block mounting option for my style range included with the repair kit would not allow me to utilize the screw for the third wire on the left rear burner. I used a drill to carefully widen the hole in the mount to make the original screw fit as there are no screws included with the kit. This added the extra time to complete the repair. Over all the repair was simple to complete but having to modify the terminal block mount was dissapointing considering the web site selected parts for my specific model number. Still a bargain compared to what a service call or new purchase costs. I will be reparing my ranges from now on.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!