R30BCH1 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sherry from Gainesville, GA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven heating element quit working.
I had a friend come..He unpluged the old one and put the new one in when it arrived. All is well. Thank you for having the part that was needed. Now the over works super..
S.Bullock
S.Bullock
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from saint john, IN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Cooking coil broke in half
Had to drill 2 new holes 1/4 lower in oven so new coil would bolt up evenly besides that it went easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Genoa, WV
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
the oven element went out
took off the back of the stove..first Unplugged it! and undid the old unit, and put the new one on....easy peasy!..Thanks for your fast mailing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Seattle, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced bake element which had burned out
Removed sheet metal plate from back of oven. Disconnected two lead from existing bake element. Removed existing bake element, replaced with new one. Connected wires, replaced sheet metal.
The trick with this old oven is to access the wires from the back.
The trick with this old oven is to access the wires from the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BERNARD from Montgomery, AL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad Element/ burned out
I unhooked element from wall on inside. Only two screws to undo. I then took back of stove off and unhook speaker like connectors. It was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashlea from Bonham, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking Element went out!
Just removed nuts. Pulled out the element from the unit. Disconnected each end. Reconnected new element. Pushed piece back into insulated unit. Attached nuts. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from Smithfield, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
My oven just didn't heat one day!
We tested all of the other "functions" of the oven to make sure that everything else worked fine, and we realized that the problem really had to be the element.
We ordered it and it came within 72 hours! We simply unscrewed the faulty element, made sure that the wires were handled carefully (circuit turned off!), and inserted the new element and rewired and screwed back into place the screws that were removed.
Simple as pie! You can do this! You don't need a service call for this one guys! Get BRAVE!!
We ordered it and it came within 72 hours! We simply unscrewed the faulty element, made sure that the wires were handled carefully (circuit turned off!), and inserted the new element and rewired and screwed back into place the screws that were removed.
Simple as pie! You can do this! You don't need a service call for this one guys! Get BRAVE!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from somerset, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the bake element
Removed the elments2 screws, unhooked the two wires, removed the rear cover from back. I then installed the new element, covered the termanals with electric tape replaced the rear cover screwed down the new element, tested.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bloomington, MN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
heating /baking element burned out
They don't make appliances this easy to repair anymore. just as others say: screw out, unhook element ..hook new one to wires, screws back in.. you're DONE.. Thanks for great service and very quick delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannette from West Jordan, UT
- Parts Used:
- 5303051519
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Bake element broke
I just followed the instructions that I found online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from edmore, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake part of oven would not heat, element fried in many areas
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Spokane, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Burned out oven bake element (bottom element).
***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Spencer, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Oven wouldn't heat as element was burned out
I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from River Forest, IL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven baking element would not heat up.
First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Louise from Swartz Creek, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Broken element on my bottom oven
The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.
Was this instruction helpful to you?
Thank you for voting!