FEFBMZ96FCC Frigidaire Range - Instructions

Followed the instruction printed on the page, while ordering the part.

Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

Replaced the dual element switch and that fixed it up

Unplugged unit and removed back panel with nut driver. Removed door, racks and unscrewed element braces from back of unit. Removed element and installed the new one. Reversed the process and then ran the unit through a preheat cycle to test it.

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Replacing the bake element in the oven was easy once I figured out which tool to use. I initially thought I needed a hex key but saw from a previous commenter that a nut driver is needed. I was able to attach it to a power drill to unscrew the nuts. once the plate was released it was easy to unhinge and install the new element. Be sure to turn off the electricity as the stove is on a 220 line.

Twisted replacement bulb into place easily. Let there be light!

My husband followed the video instructions and it was easy to fix.

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

remove power (unplug) remove screws from element unplug element replug new element replace screws reconnect power bake cookies until something else breaks.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

removed the old burner and put the new one in it's place.

First I pulled the unit away from the wall and unplugged it. There are a few screws that hold the top in place - access them from the top/front/underside of the main top - pull open the oven door to get to them. Once these were out, I gently slid the main top forward. There are tabs in the back that fit in slots just under the control panel - just work them free as you slide. I slid the top forward enough to get past a narrow aluminum plate/tab (part #26B) in the very front that runs the width of the top. Once it's free of the tabs in the back, and the front is free, there is enough play in the wires & elements to move the top to one side of the stove and access the heating elements underneath. The heating elements are attached to brackets; the brackets (part# 26) are attached to the main top. You can leave the elements & wires attached to the brackets - there is one screw per bracket that attaches it to the main top - just remove the bracket screws. It requires either a square screw driver or a 1/4 inch socket. Do one side, then the other NOTE WHICH HOLE THE SCREW GOES IN, as there are a few to choose from. After the brackets were free, the top comes off. I moved the back tabs (part #18) from the old top to the new - NOTE THE ORIENTATION OF THE TABS. I didn't, and had to flip them over, after 20 frustrating minutes. With the new tabs in, I replaced the heating element brackets, then slid the main top back to its original position. If the tabs are in the right position (see above) it'll slide right into place. I had to work the narrow metal plate in the front under the main top with my fingers when sliding it back on. I replaced the front screws underneath, plugged it back in, pushed into place, and it's working fine. About 40 minutes total, extra if you don't note the orientation of the tabs in back, or the location of the element bracket screws. The oversized heating element won't let you put it in incorrectly.