F64S352BDA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Manasquan, NJ
- Parts Used:
- 316495901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- max from antioch, IL
- Parts Used:
- 5303935068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broiler wouldnt fire
followed the excellent posted instructions. The hardest part was cleaning up the area behind the stove that hadn't seen daylight in years.
Was this instruction helpful to you?
Thank you for voting!
ice maker tray was leaking water from tray.
i took 3 screws from ice maker,then unpluged from frig.i then transferred cable to new ice maker and installed back into freezer. very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Pittsburgh, PA
- Parts Used:
- 316032000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove would not ignite on rf burner, sometimes when jiggling knob it would lite
Unplugged appliance,Removed all knobs,they pull off,removed front panel that the knobs protrude thru, 1screw right.End and left end, 2screws going downward thru burner assy, 2screws from oven opening ,,accessible with oven door open,,, slid igniter off of gas valve, disconnected wires from old igniter ,slid new igniter into same spot, reconnected wires,reinstalled frt panel,, plug it in,,, done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audrey from Miami, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rear guide clips were broken
This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Smithville, TN
- Parts Used:
- 316109512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
took the new one out of the package and put it on. Took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
Storage drawer was hanging down.
Followed the instructional video , removed the drawer, popped out the damaged part, inserted the new part, replaced the drawer. Didn't need any tools and the job took less than 10 minutes to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Cincinnati, OH
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed an extra oven rack to bake more at one time.
I just installed the extra rack and re-arranged the existing ones. Works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Fort Wayne, IN
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old oven racks were nasty!
We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from duluth, MN
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken drawer glide
I am a total non repairman. but with the video on how to I did'nt even brake the first part. ( I ordered 2 just in case)Will use you ror every part!
Was this instruction helpful to you?
Thank you for voting!
Broken Drawer slide
I just popped the broken piece out and popped the new one in! Can't believe I had a broken drawer for so long when it took less time to fix than to find scissors to open the package! Thank you for the timely and inexpensive part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Baytown, TX
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom drawer glide had snapped off
It was so easy -- took less than 15 minutes. I am a 75 year old woman and it was a snap!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Phoenix, AZ
- Parts Used:
- 316011200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Burner would not light because of cracked ceramic collar
The electrode was sparking to ground through the cracked ceramic rather than within the ignition zone. I used spray electronic contact cleaner to free rusted screws (different metals often contract at different rates and separate under the very cold spray). Replacing the electrode was a simple substitution. Also sprayed the spade terminal pair to remove any corrosion. Worked first time.
Was this instruction helpful to you?
Thank you for voting!