FEFL68GMA Frigidaire Range - Instructions

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

After replacing the oven temp sensor, with no success of correction, i purchased and installed the electronic control board. After turning off the power at the breaker and unplugging the stove, I simply removed the top back cover, unclipped the wiring harness, unhooked the 5 oven element wires(writing the color and order for easier reconnection), removed the screws, carefully peeled the face plate off the old control board and re-installed everything in reverse order. Took me all of ten minutes and the oven works like new again.

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Replaced the dual element switch and that fixed it up

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

My husband followed the video instructions and it was easy to fix.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

First I pulled the unit away from the wall and unplugged it. There are a few screws that hold the top in place - access them from the top/front/underside of the main top - pull open the oven door to get to them. Once these were out, I gently slid the main top forward. There are tabs in the back that fit in slots just under the control panel - just work them free as you slide. I slid the top forward enough to get past a narrow aluminum plate/tab (part #26B) in the very front that runs the width of the top. Once it's free of the tabs in the back, and the front is free, there is enough play in the wires & elements to move the top to one side of the stove and access the heating elements underneath. The heating elements are attached to brackets; the brackets (part# 26) are attached to the main top. You can leave the elements & wires attached to the brackets - there is one screw per bracket that attaches it to the main top - just remove the bracket screws. It requires either a square screw driver or a 1/4 inch socket. Do one side, then the other NOTE WHICH HOLE THE SCREW GOES IN, as there are a few to choose from. After the brackets were free, the top comes off. I moved the back tabs (part #18) from the old top to the new - NOTE THE ORIENTATION OF THE TABS. I didn't, and had to flip them over, after 20 frustrating minutes. With the new tabs in, I replaced the heating element brackets, then slid the main top back to its original position. If the tabs are in the right position (see above) it'll slide right into place. I had to work the narrow metal plate in the front under the main top with my fingers when sliding it back on. I replaced the front screws underneath, plugged it back in, pushed into place, and it's working fine. About 40 minutes total, extra if you don't note the orientation of the tabs in back, or the location of the element bracket screws. The oversized heating element won't let you put it in incorrectly.

Needed just a screw driver, removed the top back cover and unplugged two wire sets. Four screws and the mother board was off. My only problem was the facial front ended up pulling off some of the almond color when I pulled it off, even after I used a heat gun to soften the glue. Besides that it was very easy to fix and the range works perfectly again.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Took out 2 screws, removed panel.
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align

removed the old burner and put the new one in it's place.

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.