Models > FCS367CHSA > Instructions

FCS367CHSA Frigidaire Range - Instructions

Jump to:

All Instructions for the FCS367CHSA

Customer:: Robert R from Lewistown, PA
Parts Used:: 5304505695
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins

Two of theTop gas burners would not spark

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sue from Lampasas, TX
Parts Used:: 5304409888
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sharon from Foley, AL
Parts Used:: 5304524341, 316538904
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gerald from Artesia, NM
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Coil melted in half.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Was this instruction helpful to you?

Customer:: Robert from Glasgow, MT
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Was this instruction helpful to you?

Customer:: BETSY from HENDERSONVILLE, NC
Parts Used:: 318053103
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Door gasket was worn, stained and needed replaced

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Was this instruction helpful to you?

Customer:: Catherine from San Saba, TX
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Bottom element in oven not heating.

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.

Was this instruction helpful to you?

Customer:: Michael from Whitsett, NC
Parts Used:: 318394803
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

Convection oven fan would not stay on.

Figured out that light and door switch started the convection fan on when door is closed. Found the switch defective. Found exploded view online of switch in oven. Had to figure out that the range top needed to be removed to access the switch from inside the top part of oven. Unscrewed at least (6) screws to free up the range top. Squeezed the inside switch clips to allow switch to be pulled out from outside of oven. Disconnected electrical receptacle and plugged into new switch. Pushed in new switch til it snapped into place. Reinstalled range top.

Was this instruction helpful to you?

Customer:: Richard from Oro Valley, AZ
Parts Used:: 318255605
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

broiler element burned out

watched a U-Tube video on this subject.....worked like aa charm!!

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper temperature when baking.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Was this instruction helpful to you?

Customer:: Jack from Hedgesville, WV
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Heating element burned out

Took screws loose, unplugged old one plugged in new one put screws back

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper oven heating.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Was this instruction helpful to you?

Customer:: Jeffery from Union Point, GA
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Was this instruction helpful to you?

Customer:: charlene from princeton, NJ
Parts Used:: 318041603
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Cracked Oven Glass

The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

Was this instruction helpful to you?

Customer:: Franklyn from Jupiter, FL
Parts Used:: 318041603
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Cracked inner door glass

Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

Was this instruction helpful to you?

All Instructions for the FCS367CHSA