CGLEF379DCK Frigidaire Range - Instructions

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

called around and way to much money for repair man as well as parts from local appliance repair store. They wanted 10.00 for a screw that we got from you for $3.00 same as all the other parts saved over 70.00 dollars.

quick delivery and easy repair ... like new again .

would use you again

Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

Self easy

PS Great service Super FAST.
Thanks Jesse

Unplugged unit and removed back panel with nut driver. Removed door, racks and unscrewed element braces from back of unit. Removed element and installed the new one. Reversed the process and then ran the unit through a preheat cycle to test it.

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center portion was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

Replacing the bake element in the oven was easy once I figured out which tool to use. I initially thought I needed a hex key but saw from a previous commenter that a nut driver is needed. I was able to attach it to a power drill to unscrew the nuts. once the plate was released it was easy to unhinge and install the new element. Be sure to turn off the electricity as the stove is on a 220 line.

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

Twisted replacement bulb into place easily. Let there be light!

remove power (unplug) remove screws from element unplug element replug new element replace screws reconnect power bake cookies until something else breaks.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

repair was exceptionally easy. Did not need the fiberglass tape that was mentioned in online repair steps. Just slipped the wires off and then back on the new element. Any 70 year old can do.

Quite easy: Removed the two hex head screws with a 1/4 inch nut driver. Gently pulled the old element out of the rear of the range with the connectors still attached. Next I disconnected the connectors from the element and attached a small "paper binder" clip to each of the connector wires to keep the connectors from pulling back through the "Hole". Lastly, I connected the two connectors to the new element (released the clips) and gently pushed the unit back into place and re-secured the hex screws. ALL DONE! Very very easy....

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).