VCRE3054ASF Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- raymond from irvine, CA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven not heating up
ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Browns Mills, NJ
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element broken
turn off power to oven at breaker box
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from MILTON, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven did not heat
I watched your how to video and used my voltmeter to check my baking element. I found it defective and ordered your replacement. 5 or 6 days later it arrived in the mail. I installed it per the video and my wife baked a pizza to try it out. Perfect! Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from LAKELAND, FL
- Parts Used:
- 316400601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom oven pan was warped and discolored
Unscrew the 2 screws at the back of the oven bottom pan in the range. Place new oven pan in and rescrew the 2 screws. I could not get the two screws screwed back in. Since the bottom pan cannot move from its position, I felt like the two screws were not necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from NEWPORT, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from PORT ST LUCIE, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element had hot spots, very slow heating
Turn off the power to the range. Remove oven racks. Remove the two screws and slowly pull the element out being careful not to pull the wires off. Remove the two wires then attach them to the new element. Push the element back in place, put the screws back in, turn on the power and turn on oven to make sure the problem is fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Horace from CRUMPLER, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower Heat element burned out.
1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALBANY, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Burned out bottom oven element
Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from SAINT PAUL, NE
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out in the house we rent
Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Prosser, WA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element burned out
unfastened clip at back of oven w/screwdriver. Pulled out the plug, unplugged the element. Plugged in new element, pushed back into place, refastened clip to hold it in place at back of oven.. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet*hubbard from Old Town, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating
slid the old one out and slid the new one in.turned the unit on and it works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WESTMINSTER, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No oven heat, but the broiler worked fine. All top burners worked.
Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from JACKSON, MS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned element !
replaced the element !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donise from WILLINGBORO, NJ
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element had burned out.
I followed the instruction on the web site and the installation was just like the instruction. Very quick and easy. I was so happy and now I am baking up a storm again.
Was this instruction helpful to you?
Thank you for voting!