Models > VCRC3016AWF > Instructions

VCRC3016AWF Frigidaire Range - Instructions

Jump to:

All Instructions for the VCRC3016AWF
121 - 135 of 690
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Michael from Fort Worth, TX
Parts Used:
316075103
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replace the bake element
Had to remove the old element and had problems with the element shorted on the quick disconnect. After having my son unplug the appliance and cutting the quick connect off. My son then installed a new quick disconnect and the bake element.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keri from Raleigh, NC
Parts Used:
316075103
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Oven element broke in three!
First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.

Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.

So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Laura from Hurricane, UT
Parts Used:
316075103
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Heat element burned out.
The problem I ran into Was; Having the right socket size for doing the project. After taking care of that problem it was fairly easily to disconnect the element and reconnect the new one. It's pretty self explanitory.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dale from Athens, TX
Parts Used:
316075103
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Didn't Bake
Took it off, ordered a new part and put it back on.
Ordered on Monday and got the part on Tuesday.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from INDIANAPOLIS, IN
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven would only get slightly warm.
Loosen 2 screw with a 1/4 nut driver. Pulled element out to expose connections. Carefully disconnected old element and replaced with new element. Pushed wires back into holes and replaced the screws. (Note: Be careful not to let the disconnected wires slip back through the holes. This almost happen to me)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lisa from OCEAN SPRINGS, MS
Parts Used:
316075103
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Element quit heating
Turn off power to the stove. Unscrewed the nutholding it in place, pulled the terminals out, replaced the element by sliding the new terminals in place, replaced the nuts holding it in place and done! Turn the power back on and tested. It works again!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
lee from LEES SUMMIT, MO
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Defective element
Very easy. Remove two screws, pull element forward, remove two wires, install wires on new element, push backward and reinstall the screws. Done!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Constance from MILTON TWP, ME
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
oven element did not heat
Pulled out stove and unplugged. Took off back of stove and unplugged two wires. Opened oven door and unscrewed two nut screws to remove element. Inserted new element and screwed two nut screws back. Went to back of stove and replugged.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mitchell from Sebring, FL
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
Banking Element needed replacement
For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jean from MARIETTA, GA
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Element in oven burned through
Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christina from WASHINGTON, PA
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Oven wasnt heating
Took out 2 screws unclipped the part put the new one on and i was done. Very easy fix .. Baked a cake right after to celebrate
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Blacksburg, VA
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Oven would broil but wouldn't bake
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the new element, reassembled and SHAZAM. It worked. I am not good with electrical circuit testing etc. even though I know it must be easy so after reading many stories here, I decided to start by replacing just the element and see if I got lucky. I did. No need to call expensive repairman.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve Gilliland from Delavan, WI
Parts Used:
316075103
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Element cracked and sparked, no longer functioned
I UNPLUGGED the oven (very important), then I removed the two screws that hold the element in place, pulled the element out far enough to disconnect the two wires, plugged the wires on to the new element, pushed the new element back into place, and replaced and tightend the two screws. Finally, I plugged the oven back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PAUL from FRANKLIN, NC
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
baking element out
removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Luis from Corpus Christi, TX
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
burned out unit
Too dark to see, so left the power on so I cold use the oven light. Big mistake, shorted the fuse at the main box. No power in part of the house until finally figured out how to trip the fuse back on. Lesson learned. Never work on anything electrical without first turning off the power.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the VCRC3016AWF
121 - 135 of 690