FCRG3052ASE Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Garland Futrell from CHESAPEAKE, VA
- Parts Used:
- 5304503232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken ; oven door inner glass
Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from GAINESVILLE, GA
- Parts Used:
- 5304524341
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from CANYON LAKE, TX
- Parts Used:
- 5304498835
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The seal around the oven door had frayed on the end and come loose.
We carefully pulled the old seal out of the door ( staples hold it in place).Then took the replacement and laid it around the door. Starting at one side we adjusted the seal and pushed the staples into place. Making sure we folded the ends, we used a spoon to push them into the slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from CLINTON TWP, MI
- Parts Used:
- 316404400
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Replaced Bake Burner Tube on Frigidaire Gas Range Model FGGF3058RFC
The installation of the bake burner tube went well. I followed the instructions within the Video as it pertains to replacing the Bake igniter. That video also describes the removal and replacement of the bake burner tube. The original screws that mounted the igniter to the burner tube bracket were damaged. I replaced them with 18-8 Stainless Steel Serrated-Flange Hex Head Screws, 8-32 Thread Size, 3/8" long. As noted in the video, the oven bottom panel is removed using a flat head screwdriver. For all other screws I used a 1/4" socket and ratchet. A Nut Driver would have also worked just as well. On initial start-up after the repair there was a minor light odor from the flame coming into contact with the new metal burner tube that dissipated within a few moments. In all everything went very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CLEARFIELD, PA
- Parts Used:
- 316489403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven wasn’t getting hot, ignitor stopped working
Unplugged oven range, removed oven door (makes the work much easier, you can find how on YouTube) removed two bottom panels. Removed warming drawer to gain access to wires. Traced wire from ignitor unplugged it. Unscrewed ignitor from bracket. Carefully screwed new ignitor onto bracket. Plugged it in. Plugged in oven range. Turned on oven to verify proper operation. Turned off oven once it lit for a few seconds then replaced warming drawer, bottom panels and oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from CLEVELAND, OH
- Parts Used:
- 316489403
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Igniter Burned Out
I followed the guidance of the YouTube video presented by Steve from your company. It was very easy and direct. The only issue I had was disconnecting the igniter clip, once I wa able to remove the old one, everything else was simple. I really appreciate this video because it saved me a ton of money for repair cost. I will use this process again even if it is my refrigerator because it is a Frigidaire also. Thanks to Steve who was very direct, on point, and patient with making this repair video. Kudos!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from HOUSTON, TX
- Parts Used:
- 316489403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Stove stopped heating
Removed old Oven Bake igniter, aligned it and installed the new Oven Bake Igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from VERMONTVILLE, NY
- Parts Used:
- 316489403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The oven wouldn't lite.
I follow the instructions that I received from the e-mail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
The range at a round burner and the wife wanted an oblong one
Removed 2 3/16 bolts and burner, set the oblong burner over the orifice and we were all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from KIRKLAND, WA
- Parts Used:
- 5304517905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glide replacement
Drawer glide came off oven drawer. Wish I had taken old part off and inspected more closely. I thought tab had broke off. Turns out these glides are made of steel and very robust. However the drawer is soft sheet metal. I took off the old glide and turned out it was fine. Tab just popped out. But there was a burr on drawer i had to file off to get back on. So my advice is take old glide off first and inspect carefully.
Was this instruction helpful to you?
Thank you for voting!