Models > SCRE3054AWE > Instructions

SCRE3054AWE Frigidaire Range - Instructions

Jump to:

All Instructions for the SCRE3054AWE
121 - 135 of 693
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Donise from WILLINGBORO, NJ
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The bake element had burned out.
I followed the instruction on the web site and the installation was just like the instruction. Very quick and easy. I was so happy and now I am baking up a storm again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from wilmington, DE
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Fried baking element
Unplugged stove, removed screws holding element In place. Pulled element forward exposing electrical ends. Removed connectors, re- connected ends to new element. Pushed element back into holes and reconnected the screws. Plug stove back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from ROCKVILLE, MD
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Broken element
Simple installation took 2 minutes to do...pop on the connectors, screw each end into back of oven...DONE.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
janet*hubbard from Old Town, FL
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
oven not heating
slid the old one out and slid the new one in.turned the unit on and it works
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from WESTMINSTER, MD
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
No oven heat, but the broiler worked fine. All top burners worked.
Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BILLY from JACKSON, MS
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burned element !
replaced the element !
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Victor A from ATTICA, NY
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burnt bake element
open the door take out the racks.unscrew the holding screws for the element,pull it away from the back wall of the oven. take off the wires carefully and reverse the procedure
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from JAMES STORE, VA
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Bottom oven element was burnt out
Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Albert from STUART, FL
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bake element burnt out and snapped and appeared to try to arc-weld itself back together?!!
Just followed the very simple video instructions…it took less than 5 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rose from BADEN, PA
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
element in oven shorted out and started on fire
really easy unscrew the element from the back of the oven unclip remove old one slide clip on the new one and screw back to back of oven. Took 10 minutes or less
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from KLAMATH FALLS, OR
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Bake element burnt in half
All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RAYMOND from JONESBOROUGH, TN
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Burn into
Remove the old one and replaced the new one. It was very simple, fast, and easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from CLEVER, MO
Parts Used:
316075103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Bake element cracked and stopped working
Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
carol from LAUREL, MD
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marion from NEWPORT, TN
Parts Used:
316075103
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SCRE3054AWE
121 - 135 of 693