CFEF312FBA Frigidaire Range - Instructions

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.

The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

first i remove cover, then i unscrew defective part, remove wires. i then install new part & replace marked wires . I then replace cover, turn on oven and holla! my oven is working.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.

bought drip bowl from big box store and the 8 inch did not fit . yours fit perfect will use you for future diy jobs thank you

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

Watch video. This oven had the connecters that popped off and on which made this task easy.

Unplug the stove or disconnect at the breaker. Open the oven and remove the bake racks. Using a nut driver (or Phillips Screwdriver) remove the screws (one per side) that secure the bake element. Place them in a safe/secure place outside of the oven. Carefully pull straight back on the element until about 3 inches of the wire, that connects to the element, is exposed. Carefully unplug the wire from each element (make sure that the wire does not pull back into the oven insulation. I placed a small metal clip on each wire). Remove the old element and plug the new one in. Put everything back in the exact same way you took the old one out. Power the oven up and preheat your oven. Monitor this - should be no problem at all. Very simple process. My first attempt at this and it was very easy.

purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.