FES365EBB Frigidaire Range - Instructions

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

Husband made install in very short time. Nice to have them back in operation.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

watched a U-Tube video on this subject.....worked like aa charm!!

After searching to find the right part to replace this i found this company on line. I still could not find the part so contacted them directly and the nice woman who answered found the exact part we needed. It was shipped to us in perfect condition and we did the install ourselves with the installation help that was included with the part. We are so thankful we found this company and were able to fix our broken door. Would recommend them very highly.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Turned of breaker to stove. Removed knobs. Removed four plastic nuts under knobs. Removed five screws that hold swith plate in place. Removed two screws that held actual switch in place. Swaped one wire at a time to new switches. (Switch was a newer model so seeing switch markings was critical to correct wire replacement!) Installed in reverse order. All in all. The job was easy and the new swith looks to be of a higher quality. This ia a gee-wiz--when the old switch failed it failed to the full on position. I had a pot of chicken slowly simering on Lo went to the garage to work a project came back in to a house filled w smoke/alarms going off and the burner on full high-glowing! The old switch was dangerous!

Turn off the breaker! Remove the switch knobs. Using a Phillips screwdriver remove the two screws on the affected switch. With a large tip Phillips remove the three screws at the edge of each end of the panel and place it bottom side up on the stove top. Look at the bottom of the switch. Compare those numbers with the numbers on the new switch. Remove the wires one at a time and place them on the corresponding numbered terminal on the new switch. Be sure to put the mounting plate on the stem. Place the new switch in the cover plate and insert screws. Put cover over switches and insert the three screws on each side. Turn breaker on and turn burner switch on. Success!

Figured out that light and door switch started the convection fan on when door is closed. Found the switch defective. Found exploded view online of switch in oven. Had to figure out that the range top needed to be removed to access the switch from inside the top part of oven. Unscrewed at least (6) screws to free up the range top. Squeezed the inside switch clips to allow switch to be pulled out from outside of oven. Disconnected electrical receptacle and plugged into new switch. Pushed in new switch til it snapped into place. Reinstalled range top.

In order to service the switches on this model, remove all four knobs for the switches. This will expose the plastic nuts which hold the fascia panel secure. Remove those nuts and the fascia panel. Next use a phillips screwdriver to unsecure the steel panel which secures all four burner switches. Remove the faulty switch, taking note of each color lead and terminal designation. Replace in reverse order.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.