MEF302PBWF Frigidaire Range - Instructions

Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.

I'm a stay at home mom so when the oven didn't heat up I through oh no I have to get a new one. Well who can afford to get a new oven right after christmas. So I played with it to see if the other parts still worked, when I found that they did, I googled the the Appliance name, that is when PartSelect showed up and they had a video on how to replace the bake element. It looked doable so I ordered the part and it really was a easy fix. It took less than 10min all I had to do was pull out the old element and put in the new element. Only trouble I had was, I had to bend the prongs alittle but that was no problem. Thankyou PartSelect

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.

Received the order the next day. Unpluged the stove from electricity. Used a 1/4 craftsman wrench to undue the screws. Pulled the old one out and disconnected the conection. Reconnected the new one. Pushed back in place, then re-tightened the screws. Thanks for having it in stock.

The repair was pretty easy with the help of your on-line diagram. Other than the fact my husband failed to turn off power to the stove. Needless to say he got a small shock by the stove, Once he turned off power it went fast and safe.

Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.

At first I used a nutdriver to remove the two inside screws and found that one of the wires were not long enough to disconnect. I had to remove an access panel in the back which only had 5 screws to remove. I took it off, replaced the element and put it all back together. Then my wife tested it by baking an angel food cake which turned out perfect.

My husband had no problems except the end of the new element was different than the original, but hooked it up ok!

Replaced the baking element by removing two small sheet metal screws and unfastening the two medal clip/leads. Replaced the heating element, reconnected the leads, and refastened the screws. Took not much more then 5 to 10 minutes and the oven now heats perfectly.

Unplugged stove. Removed oven racks. Using 1/4" nut driver I removed two screws from back wall of oven that were holding bake element in place. Pulled stove from wall, removed lower back panel. Disconnected electric saber connectors. Pulled old element from oven. Put new element in oven. Reinstalled the two 1/4" screws. At the back of the stove, I reconnected the two push-on saber connections. Replaced back panel. Pushed stove back in place. Plugged in the power cord. Checked oven. Works fine.Great experience with Parts Select in every way.Total work time: about 20 minutes.