FCRC3005AWB Frigidaire Range - Instructions

took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D

From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.

I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

Turned off electric,removed rear panel and replaced part.oven is now operating good as new.

move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps

TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.

I opened the door of the gas range and slid the rack in. No one can do this! I am amazing.

I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

Watched your video and quickly made the repair. I did have to remove the back of the oven (4 screws) to connect the electrical leads to the element. Frigidaire uses a wire harness that prevent you from pulling the wires into the oven to disconnect them as the video shows. No problem; a really easy fix.