KF211KDW1 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from CHEWELAH, WA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from ROANOKE, WV
- Parts Used:
- 318348800
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
right hinge on oven door broke. door would no longer shut, losing much heat.
Remove drawer, remove oven door, remove hinge and pieces. Get the spring loose. Attache new hinge to frame, reconnect spring. Slide door back on hinges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bennie from Kite, GA
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner will not cool down. I have to switch all the way off.
First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from MAY'S LANDING, NJ
- Parts Used:
- 318348801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken hinge
Replaced same very simple.
Was this instruction helpful to you?
Thank you for voting!
Pulled the heating element on each burner installed the drip pans.
They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from TEMPLE, GA
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating coils stop heating
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from MENASHA, WI
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burner elements not heating
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josephine from Malden, MA
- Parts Used:
- 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pitted, Eroded Drip Pans
1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.
Was this instruction helpful to you?
Thank you for voting!
This is for a basic four-burner electric stove:One element was bent so I replaced it and all of the drips bowls needed replacing.
The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Charlotte, NC
- Parts Used:
- 318372210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Left rear burner had a damaged burner prong.
I just had to plug the new burner plate in the receptical
and it works again very well.
and it works again very well.
Was this instruction helpful to you?
Thank you for voting!
Old Drip Bowls Corroded beyond Repair
I've been to many appliance repair stores looking for White-Westinghouse Stove Parts and have been told their 'unavailable'! Then I checked PartsSelect.com- and they were listed as 'available'. The 6" & 8" Drip Bowls shipped quick and arrived packed well. The new Drip Bowls aren't as heavily made as the originals- but they are exact replacements and very easy to replace. The wife is happy and with many replacement parts & how-to-videos for repair we plan on keeping this stove for another 20 years!
Was this instruction helpful to you?
Thank you for voting!