FFES3015PWG Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pat from GREELEY, CO
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element burned out
All you do it unplug the old one and plug in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from WEATOGUE, CT
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original Element physically broke
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDGAR, WI
- Parts Used:
- 5304504897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
sensor should pull into oven enough to easily unsnap and snap but didn't pull out
on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PALATKA, FL
- Parts Used:
- 316419137
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Had a F1 code on the range, could not control the bake temp.
Replace the electronic control board & overlay. Tested, works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny L from CHELAN, WA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heavy jam boiler caused elements to sag
Removed the old & simply inserted the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Spencer, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Storm Lake, IA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dead burner
I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!
Rusted Drip Bowls
This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from WILLOW SPRING, NC
- Parts Used:
- 5304504897
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven was kicking out error code F1
First, I shut the OFF the main breaker. Then, I removed 2 screws holding the thermostat inside the oven. The wiring harness was too short to pull through small opening. I tried to fish the wires out with a piece of wire, but no luck. Eventually, the wiring harness disconnected and I had no choice but to remove entire wall oven from wall cavity.
Before starting this, again, make sure the main breaker is OFF:
1. Remove 2 screws that hold the oven in place. Mine were just below the display panel.
2. Remove silver trim at bottom of oven.
3. The power cable (flexible conduit, running down to the floor inside the cabinet) was too short to pull the oven out of the wall. I had to disconnect the oven wiring at the junction box (again...make sure the main breaker is OFF). I photographed the wiring set-up before disconnecting any wires. Once disconnected, I was able to pull the oven out of the wall cavity.
4. I placed the oven unit on a bar-height stool with a blanket underneath.
5. I removed the sheet metal shield on the back of the oven. (Roughly 10 screws on the sides.)
6. I found the wires to the old thermostat and pulled it through the opening in the back.
7. I disconnected the old thermostat harness, connected the new one.
8. I pushed the new thermostat into the oven and reconnected the 2 screws.
9. Everything looked good. I reassembled the back, slid the oven into the wall.
10. Reconnected the wiring.
11. Turned the breaker back on. Tested and it worked.
12. Secured the stove and installed the trim.
Before starting this, again, make sure the main breaker is OFF:
1. Remove 2 screws that hold the oven in place. Mine were just below the display panel.
2. Remove silver trim at bottom of oven.
3. The power cable (flexible conduit, running down to the floor inside the cabinet) was too short to pull the oven out of the wall. I had to disconnect the oven wiring at the junction box (again...make sure the main breaker is OFF). I photographed the wiring set-up before disconnecting any wires. Once disconnected, I was able to pull the oven out of the wall cavity.
4. I placed the oven unit on a bar-height stool with a blanket underneath.
5. I removed the sheet metal shield on the back of the oven. (Roughly 10 screws on the sides.)
6. I found the wires to the old thermostat and pulled it through the opening in the back.
7. I disconnected the old thermostat harness, connected the new one.
8. I pushed the new thermostat into the oven and reconnected the 2 screws.
9. Everything looked good. I reassembled the back, slid the oven into the wall.
10. Reconnected the wiring.
11. Turned the breaker back on. Tested and it worked.
12. Secured the stove and installed the trim.
Was this instruction helpful to you?
Thank you for voting!