CFEF3051TWB Frigidaire Range - Instructions

replaced it

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

real easy with no problems, thank you

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Removed outer glass first ,then worked my way thru to inner glass..

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

My brother is a licensed electrician, so the job was relatively easy for him. The pieces of insulation were pre-cut to fit, so there was no trimming involved. He tilted the oven over on its back to replace the piece of insulation under the oven. Removed the metal panel between the storage drawer and oven bottom, removed the soiled insulation and wiped everything down with vinegar. Placed the new insulation and reinstalled the metal panel and drawer. Removed the oven/range top and again removed the soiled insulation, wiped everything down and installed the new insulation (this piece of insulation was the wrap around one that goes under the range top - across the top of the oven and down both sides). Replaced the oven top, then did the back panel - this one was the most time consuming, due to the need to disconnect some of the wiring and sensors, as well as having to loosen the panel where the control knobs are located in order to remove the inner panel to get to the insulation. The insulation was precut to fit around the oven light bulb, so just had to make sure we installed it right side up :). Have used the oven several times since and no more smell!!

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.

take back planel off, take wires off old element and intsall new element hookup wires, put back planel ..under one hour job

I followed the Parts Select Video that showed replacing an identical switch. Mine were another brand & style with different color wires. I took a picture of 1 to keep track of the wiring and removed it. I saw that the terminals were marked P, H1, H2, L1, & L2 so I put the wire from the same terminal onto the Parts Select switches & they work just fine now. The parts I got from you are heavier and a much better quality than the original equipment. I would also like to say that I was amazed at how fast this order was shipped, and the washer pump was a piece of cake thanks to your video.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

WE watched the installation videos first. Very helpful. Removed rear hood cover, jotted down wiring connections, ensured that the brackets were secure ( one was not ), applied overlay,attached wires and tightened 4 screws( not supplied ). On-line photo was upside down but was the correct part. Delivery was prompt.