CFEF3052TSC Frigidaire Range - Instructions

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

Looked up the appliance and the suspect part.(clock/timer). It described the part and what problem it would fix.(no power to oven) Part shipped very fast and installation was quick and easy!!! They even had a installation video!! You can`t get any better than that!!!

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Statistics said it was the element. I replaced that this did not correct problem. Went with the second statistic and it was correct. I showed the video to my tenant and he replaced it and called me in a few minutes saying it worked fine. Look at the video then it will be easy for you. The only thing in the video that was not clear is that you have to peel the sticker off of the front of the old clock and attach it to the new one. Everything else is exactly like it says.

I watched the video to make sure I understood what I needed to do. I did just as the video right down to installing the new one before replacing the wires, which was the hardest part the connectors were on tight. Replaced all screws tested to see if oven worked which it did. Thanks for the video.

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

I thought I was going to have to purchase a new stove which I could not afford, repair man would have cost over $300 to repair. I went on this wedsite, matched the part number with my stove, spoke with customer service, (very good experience), ordered parts, received in approximately 2 days,watched a brief (2 minute)video that came with my confirmation email and TA DAH.....fixed for 1/3 of the repairmems price and so easy. Thanks so much Partselect. Diane

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Removed five screws from back of range top with nut driver.Lifted wire connectors(4).Replaced old control board with new one.Replaced screws.And Bingo!The whole procedure took about 15 minutes.

Took off back of oven, detached old clock piece, attached new one, put back panel back, done.

After a power outage or bake and broil features stopped working, but the rest of the appliance worked fine. I wasn't sure if it was the clock part or the temp probe, but decided the cost replacing both parts was less than a repairman. So first, I watched the video link on the part's page...extremely helpful! Then it was a matter of a few screws and unplugging and re-plugging a few wires. I have NO electrical experience, and very little handy-man experience. This is a simple repair that anyone could do. I am most amazed with PartSelect because it literally took 24 hrs after placing the order for it to arrive on my doorstep. And it saved us an estimated $175 in repairman labor fees. I will be telling everyone about our great experience. Thank you!