FFEF3003UWB Frigidaire Range - Instructions

Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!

Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on

I watched the video on how to do it

All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.

Watch the easy install video a couple of times and easy as a piece of cake!

Unscrewed 2 screws, pulled the wires out and unplugged the old element, plugged the new one in, screwed 2 screws back in, so easy anyone can do this, it's nice to have a second person holding a flashlight but couldn't be any easier.

Since I had the element out I cleaned the stove. That took me 2.5 hours. Used cold spray and let sit for two hours and wipe out clean took about 30 minutes. Now for the element itself it took me about five minutes to put the new one in. Oven looks and works like new. Just google your repair needed and watch the video. Easy Peasy. Last time I had it done by an electoral repair person for the tune of about $100.00. This time I bought the part and did it my self. Cost less than $25.00 including tax and shipping. No brainer.

Took out 2 screws unclipped the part put the new one on and i was done. Very easy fix .. Baked a cake right after to celebrate

My part was the oven burner for my Tappan stove. I followed a very helpful you tube video. All I had to do was use 1/4" screw-type screwdriver (not sure what you call it), remove screw, pull out each side, pull part away from wire; and then insert the new oven burner!! SIMPLE and I'm a 68-year old widow! I was proud.

Removed the defective part. Install the new part, insert the connectors. Now its working

I flipped the 220 circuit breaker to shut off the electricity. I unscrewed the old element (2 screws). One problem I ran into was that there was insulation packed tight around the old wire, so when I went to pull it out one of the connectors came undone. So I had to take the small plate off the back of the stove and fish the wire back through. I connected the new wires and screwed the element to the back. I only needed a square head screw-driver for the whole job. It would've taken me 5 minutes if I wouldn't have had to fish the wire back through. Still, it only took around 20 minutes and was really easy. The element cost me less than half of what an appliance repair shop charged. I'm a woman, and I've never attempted anything like this before but the video made it so easy to do! Thanks for saving me a bundle of money!

Using small square tip screwdriver (#1 if my memory is correct), removed two screws at rear of oven pulled old element carefully by pulling, removed wire from each side, attached wires to new element, slid to back feeding wire back where they had been, put screws back in, tightened and viola, stove working great. Approximate time to do job, less than ten minutes!

Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.

Turn off power to the stove. Unscrewed the nutholding it in place, pulled the terminals out, replaced the element by sliding the new terminals in place, replaced the nuts holding it in place and done! Turn the power back on and tested. It works again!

I sat on a stool and knelt on a pillow (because of my knees) but I got it done and it works great!!