CFEF3012UWB Frigidaire Range - Instructions

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

I watched the video to make sure I understood what I needed to do. I did just as the video right down to installing the new one before replacing the wires, which was the hardest part the connectors were on tight. Replaced all screws tested to see if oven worked which it did. Thanks for the video.

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

I thought I was going to have to purchase a new stove which I could not afford, repair man would have cost over $300 to repair. I went on this wedsite, matched the part number with my stove, spoke with customer service, (very good experience), ordered parts, received in approximately 2 days,watched a brief (2 minute)video that came with my confirmation email and TA DAH.....fixed for 1/3 of the repairmems price and so easy. Thanks so much Partselect. Diane

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Took off back of oven, detached old clock piece, attached new one, put back panel back, done.

After confirming that the renter had broken the timer through frustration I ordered the correct part and fixed the problem.After removing the rear panel it was obvious the timer was broken..just put wires where needed and reinstalled the new clock timer..The oven worked like new..

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

After a power outage or bake and broil features stopped working, but the rest of the appliance worked fine. I wasn't sure if it was the clock part or the temp probe, but decided the cost replacing both parts was less than a repairman. So first, I watched the video link on the part's page...extremely helpful! Then it was a matter of a few screws and unplugging and re-plugging a few wires. I have NO electrical experience, and very little handy-man experience. This is a simple repair that anyone could do. I am most amazed with PartSelect because it literally took 24 hrs after placing the order for it to arrive on my doorstep. And it saved us an estimated $175 in repairman labor fees. I will be telling everyone about our great experience. Thank you!

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,