FCRE305CASA Frigidaire Range - Instructions

This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.

took out the old one, screwed in the new one. very easy.

Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.

Remove screws pull off wires and install new parts

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.