F64C353BTA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from lexington park, MD
- Parts Used:
- 5303208499, 5303935068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven or boiler not lighting
removed gas safty and igniter .replaced 4 screws and 3/8 wrench. make sure you turn the gas off frist.after repairs are done make sure there are no leaks at fittings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audrey from Miami, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rear guide clips were broken
This was the easiest do it yourself repair job to be had so simple just push the new clip in the hole and you are done so easy. Audrey
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Phoenix, AZ
- Parts Used:
- 316011200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Burner would not light because of cracked ceramic collar
The electrode was sparking to ground through the cracked ceramic rather than within the ignition zone. I used spray electronic contact cleaner to free rusted screws (different metals often contract at different rates and separate under the very cold spray). Replacing the electrode was a simple substitution. Also sprayed the spade terminal pair to remove any corrosion. Worked first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Palmer, AK
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the pullout drawer below oven did not work
the rear glides were missing on the back of the drawer so the drawer would pull out but when pulled back in, would tip down and not catch on anything. I ordered the parts then found an instructional youtube and watched it. Easy repair, cheap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from El Paso, TX
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just had to replace the racks in the stove.
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks
Was this instruction helpful to you?
Thank you for voting!
Front and rear glides broke on bottom drawer.
After watching the videos on removing and replacing the front and rear glides on the bottom drawer, I was able to take the bottom drawer out, use a screwdriver to pry all the glides out of their slots and snap them all back in place in less than a minute. Without the videos I was completely helpless in knowing the sequences to performing this task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Villa Rica, GA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front drawer glide broke off and drawer had no support on left side.
Watched on-line video to confirm I was ordering correct part and installation took less than 30 seconds. Video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Miramar Beach, FL
- Parts Used:
- 5304497424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
not heating as setting reads
watched u tube sent by your company, opened back of oven,removed sensor,checked w/ohm meter,ordered part, replaced sensor,replaced back on oven, DONE! works like new amazing help I was given by your staff! I was quoted over $200.00 to come to my house,ck.,fix, and part replaced. My cost was $50.00 + shipping of $7.00. Thank you guys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Manasquan, NJ
- Parts Used:
- 316495901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Pittsburgh, PA
- Parts Used:
- 316032000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove would not ignite on rf burner, sometimes when jiggling knob it would lite
Unplugged appliance,Removed all knobs,they pull off,removed front panel that the knobs protrude thru, 1screw right.End and left end, 2screws going downward thru burner assy, 2screws from oven opening ,,accessible with oven door open,,, slid igniter off of gas valve, disconnected wires from old igniter ,slid new igniter into same spot, reconnected wires,reinstalled frt panel,, plug it in,,, done
Was this instruction helpful to you?
Thank you for voting!
one rear and one front glide missing
Just moved into this house and inherited the oven so I don't know how old it is but I had to put something down in order to submit this review. Popping the glides in place took seconds. I am amazed that I found the parts so easily online and that they arrived so quickly. Usually the simplest of things turns into a time consuming project for me. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Saint Clair Shores, MI
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sliced Outlet Cord
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Weidman, MI
- Parts Used:
- 316011200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Igniter electrode broke
The three bolts that held the burner busted off when tring to loosen. I drilled out the old studs and replaced with self tapping screws.
Was this instruction helpful to you?
Thank you for voting!