Models > CE30S6WMAC > Instructions

CE30S6WMAC Frigidaire Range - Instructions

Jump to:

All Instructions for the CE30S6WMAC
46 - 60 of 258
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Fernando from Orlando, FL
Parts Used:
316442301, 316048413
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replace Element & Drip Bowl
Just replace the parts. Too easy for an old man.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
steven from EPPING, NH
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
The bottom Heating element burned out.
I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Margaret from Spencer, OH
Parts Used:
316442301
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Danny L from CHELAN, WA
Parts Used:
316442301
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Heavy jam boiler caused elements to sag
Removed the old & simply inserted the new one
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Simon from New Port Richey, FL
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
oven heating element
I just removed two screws. Pulled the element out, unhooked the wires. plugged the wires into the new element screwed it in and was done
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dr. Johanna V. from North Conway, NH
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench set
Oven element burned out
Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kyle from Jacksonville, FL
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The old element caught fire.
Unscrew the old one and unplug the wire leads. Then plug in the new one and bolt back up.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Helen from PAWLEYS ISL, SC
Parts Used:
316048414, 316048413
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chuck from EVANSVILLE, IN
Parts Used:
5303935058
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Doris from SUN CITY, AZ
Parts Used:
316048414, 316048413
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drip bowls needed replacing
Removed the old ones and inserted the new ones.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Lake Luzerne, NY
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The bake element burned out
I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two screws. I turned the circuit braker on and the element functioned properly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Elizabethville, PA
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Lower element wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Wyndmoor, PA
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven bake element would'n heat
Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Columbus, IN
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven heating elelment stopped working
I watched my husband do this repair so if it happens again I can do it myself. He removed the screws holding the element in place, unplugged the element, plugged the new element in and replaced the screws. I am so glad I found your site. The posted pictures and measurements made finding the exact part a breeze and the element arrived in a couple of days. We saved a bundle!! Thanks.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from Alton, IL
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake element burned into two pieces.
Pulled stove out, removed screws that hold the element in place. Then pulled element out a few inches, diconnected the two wires. I connected the wires to the new element and put everything back to right. It was quick and easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CE30S6WMAC
46 - 60 of 258