MBL908M0W Frigidaire Range - Instructions

I started to work on it & in came a friend & saw a helpless female & took to the job & finished it real fast & efficently.Great repair. Gearldine

I just followed the instructions that I found online.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

first i removed the two screws that hold the element in place. then pulled out about 3 inches
and disconnected the wires.installed in reverse
order.

Easy to open package and plug in unit! Too simple and quite happy with end results!

I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.

Working on 33 year old Kenmore stove (Harvest Gold color bought in 1977). Have replaced the element every 12 to 14 years, last in 1997. 3-5 FedEx delivery took only 1 day. I verified Selector dial and Temperature dial both set to off. I took out the 2 oven shelves and took off the oven door for easier access to back of oven. Open oven door slightly to 1st catch, slightly lift and pull door away from the oven to clear the 2 side hinges from the openings. I used 1/4 inch socket with ratchet to remove 1 screw on each side holding element to back wall of oven. Gently pulled element out and up slightly so connectors come through openings in back wall. 1 connector came out from wall 4 inches, the other just barely. I used needle nose pliers to pull connector off element with 4 inches of wire. The connector did not come off easily, it took some wiggling of the connector (not too hard because it is brittle). I pulled connector off element barely out from the wall and held the connector in the pliers (did not let go). Put old element on kitchen floor and put new element on oven floor. Attached connector wire to end of element so it didn't slip through back wall. Attached connector wire to other end of element. Lifted element slightly to push through back wall openings. Used 1/4 inch socket to re-attached both screws. I put oven door back on (reverse of taking off). I set Selector to Bake and Temperature to 300. I watched element heat up (nice solid color along entire length) and reach 300 temperature and cycle off. I opened oven door to force the thermostat to kick in the cycle again. I closed oven door to watch the element again. When the heating cycle finished, I turned the Selector & Temperature to off. When oven cooled off, I put the shelves in again.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

Took the back off, and took the terminals off. Took out the old element and put the new one in and put the terminals on and screwed it back in and put the back on. And all done.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

unscrewed rear connections, removed broken element, installed new