FGF337ASJ Frigidaire Range - Instructions

I loosened two screws(one on the left and one on the right) at the inside base of the oven door, then lifting the door off. The hinges are held in place by two screws and a flat metal covering. Remove the faulty hinges. The screw holes on the new hinges have to have some WD40 applied and then screw the screws in and out to widen the holes a bit. Once the screw goes in easily, remove them and insert the hinge into the hole that you removed the old hinges from. Replace the metal covering and insert the screws. tighten the screws. Open the hinges then slip the door back onto the hinges. Reinsert the two screws at the bottom of the door and tighten. I recommend replacing both hinges as there is a plastic insert in the hinge that becomes brittle over time and breaks.

Oven would not light upon setting for oven heat-up. Igniter would glow, but no gas flow. Gas Valve safety not sensing enough current draw from igniter to open gas valve. Original igniter measured 175 Ohms on Volt-Ohmmeter. New Igniter measured 74 Ohms before installation and use. Installed and spliced into existing wires using good quality wire nuts and tucked wiring into wire areas ensuring it was away from burner flue. Oven lit on first start-up! Problem fixed! Easiest to get to by removing broiler drawer, pressing catch tangs in from outside rails using a small screwdriver. 1 screw of 2 on igniter mount was stripped and difficult to remove, but working with pliers and nut driver was able to remove it with some difficulty. New Igniter hangs fine with 1 screw. .

6 screws to remove upper back panel, 4 screws to remove control. Unplug wire harness. Carefully remove adhesive backed front display cover & press to new control, & reverse process to reinstall. Exact original replacement part, quick delivery! replacement

I didn’t follow the instructions for the igniter
I simply jerked hard on the bottom drawer & it cam out onto the floor . Pulled range out & changed the oven sensor with a nut driver.
Same for the controller, 5 screws with a nut driver to remove back plate & 4 screws holding the controller in place , used the old face plate and it was easy as pie

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed which has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arrived early than anticipated.

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

Easy installation using a nut driver and a Phillip screwdriver.plug in harness connector and done.

My daughter did the installation and it was quick. She had no problem, and it's working great. She love it. She just use a philp screwdriver to take off the bolt then unplug the control adaptor. From the back then plug the new one in and that's it. Easy as 123

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.