FCS388CEBB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from Colrain, MA
- Parts Used:
- 318328010
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
had no instructions on how to remove old door hinge recepticle..
After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Louisville, KY
- Parts Used:
- 316026105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken drawer handle
remove 8 screws and replaced handle. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert R from Lewistown, PA
- Parts Used:
- 5304505695
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Two of theTop gas burners would not spark
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Artesia, NM
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Coil melted in half.
First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Hedgesville, WV
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out
Took screws loose, unplugged old one plugged in new one put screws back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Milford, IN
- Parts Used:
- 318394803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove door switch was broken
used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bear from Royston, GA
- Parts Used:
- 316122100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two burner caps missing from Frigidaire gas stove
part match perfect, right part right price good company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Union Point, GA
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out on my oven
Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oro Valley, AZ
- Parts Used:
- 318255605
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
broiler element burned out
watched a U-Tube video on this subject.....worked like aa charm!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETSY from HENDERSONVILLE, NC
- Parts Used:
- 318053103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was worn, stained and needed replaced
Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Phoenix, AZ
- Parts Used:
- 316011200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Burner would not light because of cracked ceramic collar
The electrode was sparking to ground through the cracked ceramic rather than within the ignition zone. I used spray electronic contact cleaner to free rusted screws (different metals often contract at different rates and separate under the very cold spray). Replacing the electrode was a simple substitution. Also sprayed the spade terminal pair to remove any corrosion. Worked first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from North Smithfield, RI
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven did not work since bake element did not warm up.
Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constantine from Vero Beach, FL
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower oven element burned up
Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.
Was this instruction helpful to you?
Thank you for voting!