CFEF318ES1 Frigidaire Range - Instructions

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Took screws loose, unplugged old one plugged in new one put screws back

Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.

I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!