Models > FES367AQD > Instructions

FES367AQD Frigidaire Range - Instructions

Jump to:

All Instructions for the FES367AQD

Customer:: Kelly from Marietta, GA
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Largest burner was not operational

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

Was this instruction helpful to you?

Customer:: Jack from Hedgesville, WV
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Heating element burned out

Took screws loose, unplugged old one plugged in new one put screws back

Was this instruction helpful to you?

Customer:: Michael from Orange, TX
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

broke element.

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper temperature when baking.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Was this instruction helpful to you?

Customer:: James from Milford, IN
Parts Used:: 318394803
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Stove door switch was broken

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Was this instruction helpful to you?

Customer:: Jeffery from Union Point, GA
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Was this instruction helpful to you?

Customer:: Robert from Glasgow, MT
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Was this instruction helpful to you?

Customer:: BETSY from HENDERSONVILLE, NC
Parts Used:: 318053103
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Door gasket was worn, stained and needed replaced

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper oven heating.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Was this instruction helpful to you?

Customer:: Vista M. from Northport, AL
Parts Used:: 318293827
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Unable to control surface burner temperature

Pull range unit from wall. Disconnect power cord. Remove back panel on range(10 Phillips head screws). Pull knob from surface burner switch and remove two screws. Remove and re-connect wires from switch by number on switch. Replace switch and back range panel. Re-connect power cord and re-position range to original spot.

Was this instruction helpful to you?

Customer:: Russell from North Smithfield, RI
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Oven did not work since bake element did not warm up.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Was this instruction helpful to you?

Customer:: Constantine from Vero Beach, FL
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

lower oven element burned up

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Was this instruction helpful to you?

Customer:: Kathleen from Lawrenceville, GA
Parts Used:: 318293820
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner on top occasionally went to high heat though it was set at low

Replaced the switch...removed old switch and transferred the wires one at a time to the new switch. Seems to working fine..

Was this instruction helpful to you?

Customer:: James from Basking Ridge, NJ
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Element burned out in 15 months

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Was this instruction helpful to you?

Customer:: Patricia G from Stewart, TN
Parts Used:: 318293827
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

The switch to the large right burner went out.

Our neighbor, who is an electrician, watched the video on how to install. Since this switch was substituted, he paused the video several times to see how the wires should be attached. It worked.

Was this instruction helpful to you?

All Instructions for the FES367AQD