GF880KXD1 Frigidaire Range - Instructions

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.

took off bottom pan in oven and replaced ignitor

followed posted repair procedure on Parts select site. . . straight forward and simple. . .

i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as well with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself

I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so much money doing it myself. U to can do it, good luck!!

after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com

From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than it had for some time.

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

took out the old (2 screws) put clip on wires and put the new part in. Simple

A friend replaced the new ignitor with the old one...very simple job.

I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.

The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.

followed the instructions that come with the part. very quick and easy.

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.