KC535ADH2 Frigidaire Range - Instructions

Working on 33 year old Kenmore stove (Harvest Gold color bought in 1977). Have replaced the element every 12 to 14 years, last in 1997. 3-5 FedEx delivery took only 1 day. I verified Selector dial and Temperature dial both set to off. I took out the 2 oven shelves and took off the oven door for easier access to back of oven. Open oven door slightly to 1st catch, slightly lift and pull door away from the oven to clear the 2 side hinges from the openings. I used 1/4 inch socket with ratchet to remove 1 screw on each side holding element to back wall of oven. Gently pulled element out and up slightly so connectors come through openings in back wall. 1 connector came out from wall 4 inches, the other just barely. I used needle nose pliers to pull connector off element with 4 inches of wire. The connector did not come off easily, it took some wiggling of the connector (not too hard because it is brittle). I pulled connector off element barely out from the wall and held the connector in the pliers (did not let go). Put old element on kitchen floor and put new element on oven floor. Attached connector wire to end of element so it didn't slip through back wall. Attached connector wire to other end of element. Lifted element slightly to push through back wall openings. Used 1/4 inch socket to re-attached both screws. I put oven door back on (reverse of taking off). I set Selector to Bake and Temperature to 300. I watched element heat up (nice solid color along entire length) and reach 300 temperature and cycle off. I opened oven door to force the thermostat to kick in the cycle again. I closed oven door to watch the element again. When the heating cycle finished, I turned the Selector & Temperature to off. When oven cooled off, I put the shelves in again.

Took the back off, and took the terminals off. Took out the old element and put the new one in and put the terminals on and screwed it back in and put the back on. And all done.

Easy to open package and plug in unit! Too simple and quite happy with end results!

The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

I'm a stay at home mom so when the oven didn't heat up I through oh no I have to get a new one. Well who can afford to get a new oven right after christmas. So I played with it to see if the other parts still worked, when I found that they did, I googled the the Appliance name, that is when PartSelect showed up and they had a video on how to replace the bake element. It looked doable so I ordered the part and it really was a easy fix. It took less than 10min all I had to do was pull out the old element and put in the new element. Only trouble I had was, I had to bend the prongs alittle but that was no problem. Thankyou PartSelect

Unplugged stove, use nutdriver, removed screws, pulled out old element, put in new one. Done. As prescribed. Excellent help as well as got part the next business day.

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.

took me longer to find my 1/4 inch nut runner and drill than to change out the element.........simpliest replacement i've ever encountered and i'm 64 years old. less than 2 minutes......

Even though my exact model was not matched by Parts Select the bake element shown in a picture for a different model was correct. The length the bake element protruded through the wall of the oven was the same as the old one. The element arrived within two days, packaged so it would not be damaged en transit.

The problem was that there was heat in the oven but only a little. This threw me off at first but my wife tells me that the broiler element is used as the oven heats up. So bottom line is, the main element was burned out and once I replaced it, everything worked fine.

unscrewed rear connections, removed broken element, installed new

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.