FES350BW1 Estate Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Irmo, SC
- Parts Used:
- 814103
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Clips worn/broken
I had to remove the original clips (broken or damaged). This was the hardest part -- the clips were held on by rivets (not screws), so I had to pound/punch them out (using care so not to damage the stove top). Once I punched the rivet out all that remained was a small hole, I just used the small nut and bolt that came with my stablizer clip kit and mounted the new clips. Everything worked out fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from LEESBURG, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
large right front burner wasn't going on
turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosa from Miami, FL
- Parts Used:
- 868522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
2 Surface burner center medallions broke
Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from killingworth, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners weren't heating
Unplugged old burner elements. Popped in new burners. Turned on the burners to test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from BEND, OR
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
This burner on our range had no temperature control - it was either full-on or full-off
1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from VALE, SD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
unit burned out
grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Swanton, MD
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not stay heated had to wiggle the burner to make heat
Replaced with the new burner works like new. Thanks a bunch!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Pekin, IL
- Parts Used:
- 814103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old stabilizer clip was broken
I removed surface burner and drip pan from stove. Then drilled out the remaining part of the old stabilizer clip. Once clip was removed I installed the new stabilizer clip with the screw and nut that came with the clip. Then I placed the drip pan back into position and installed the burner and locked it into the new clip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Baldwinsville, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not heat up.
Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS C from GRAND JCT, CO
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dual burner would go to highn heat.
Watched video & did just guy in video did. Very easy job & the burner works like new.
Was this instruction helpful to you?
Thank you for voting!
8" surface element stayed on high.
Pulled range out from wall, unplugged AC, unplugged infinite switch, plugged in new switch, broke off end of stem, plugged AC in put range back and tested.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from LISLE, NY
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not control temperature for 8" burner (front right).
The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GAIL from ORCHARD PARK, NY
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front Burner Would Not Heat
I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower oven element not working.
1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.
Was this instruction helpful to you?
Thank you for voting!