TEP315TV0 Estate Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- L from Richardson, TX
- Parts Used:
- WP9761346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out coil
Simply slide out old coil by lifting cooktop pan; position new coil electirc elements in oven slots, slowly push in, then push coil tab into slot in pan for balance. No problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kyle from Schwenksville, PA
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowl
remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Misty from Glenn Heights, TX
- Parts Used:
- W10196405RW, WPW10256908, 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Purchased a house with a working oven, but without racks, broiler pan, and one missing drip pan
No real repairs, just replacement. Everything is good and now I can use my stove. Just in time for Thanksgiving!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulette J. from Connell, WA
- Parts Used:
- WP9761346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner stopped working right.
Was able to unplug the old burner and plug the new one in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from Kaiser, MO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the heating element went out.
removed the two screws and unhooked the old heating element. I set the new element in place and attached the electrical leads and replaced the two screws and tested the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Vero Beach, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip plans needed replacement
Removed old ones replaced with new oned
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dr PauMari from Alamogordo, NM
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Melted and fused together wires due to non-grounding of terminal block
We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Columbus, OH
- Parts Used:
- WPW10308477
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Bottom oven heating element burned out
Only difficult because one heating element connector broken off. Before receiving correct part, tried to install generic element, which had leads about 2 inches too long, so trying to force into place bent electrical connectors that go from oven to heating element. Tried to bend one back and it broke off, so did not bend 2nd one back. Received correct heating element, and slid unbroken connector on one element side, and soldered 2nd element on. Screwed heating element in and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Ogden, UT
- Parts Used:
- 4449746
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
the bottom hinge pin fell out and door was loose
Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for being a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Channelview, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
R&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Brazoria, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Power block terminal failure
Ordered part needed. Much, much cheaper than purching a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from kissimmee, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
top element was burnt out small burn hole in element
removed the screws that were on back side of oven securing panel that covered element terminals disconnected wiring to upper element then went in side oven area removing 4 upper mount screws that were holding upper element in place then removed old element and reinstalled new in same order was removed..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Grantsville, UT
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
terminal block back of range shorted and burned
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, NC
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element would not get red hot
Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.
Was this instruction helpful to you?
Thank you for voting!