TES400PXMQ0 Estate Range - Instructions

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Moved Oven from wall, removed eight screws holding down the Burner Top. Lifted Top and held it up to remove two screws on the side of the element. Disconnected four wires, replaced element, connected the four wires again and assembled in reverse mode of dissasembly. All went pretty simple, moving oven from wall and adjusting/level it back in place was the most time consuming.
Part works fine, delivery was faster than expected during the Holidays. Good Job Thanks!!!
HAPPY NEWYEAR!!!!

Unplug appliance first. Remove rear cover plate (only to disconnect burner plug). Remove plastic upper side covers. Open oven door & remove two screws holding burner top. Lift off entire top, flip upside down and change element.

We looked online for instructions, not sure how to "lift" the glass top.... There were 2 screws/hex head at the front of the range under the top that when removed allowed the top to be lifted up ..... the elements are on the underside, and with the removal of a few screws and unplugging the element connections (real easy) the burned out element was easily removed and the new one replaced... Less than 15 minutes for the whole operation...HOW COOL!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Instructions on line were very helpful. The only problem was getting the screws loose on the clamps that held the glass in. If I was going to redesign this door I would use Hex head screws that can be removed with a nut driver. Most of the time for the job was taken up by cleaning off accumulated grease. You will be surprised how much gunk can get inside the door.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

removed oven door from stove. Laid door on work table. Took screws out of the bottom. Flipped each layer over until I got to the interior glass. Removed broken glass and installed new glass. Flipped pieces back in place and put screws back in. Placed oven door back on stove. Easy!!

Had to screw off old terminal block & screw on new one

Replace was not quite like video. I could not remove door so I had to replace glass with door in place. I just kept removing screws until I was able to get to the door. Video helped me know what to expect, double panels, double glass, insulation, rope seal, no caulking. I took pictures with my phone when there was a bracket/spacer that was not obvious on how it went back together. Glass was the perfice size. Thanks partselect!

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS