TEP315VT0 Estate Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlton from lakeland, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element burned out
Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Brush, CO
- Parts Used:
- W10856603
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Oven doesn't heat evenly
Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Davie, FL
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Burned Out Termincal Block
I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BTW - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Palestine, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower element went out
I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Daytona Beach, AL
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
someone did not install cord properly! they left a strong strain on one of the 3 wires, with a loose nut connection that caused it to heat and melt the plastic that poped out toward the rear metal cover and short circuited.
I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Fernandina Beach, FL
- Parts Used:
- WP3195263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
I was given a stove with no door handle
I very simply removed the inside panel of the stove door with a screwdriver. With two screws and two lockwashers and a couple of nuts, I replaced the stove door handle in the already made holes and screwed the screws tight. That was it. Not complicated at all. Thank-you for all the care you gave in packing and the speedy shipping. M. Rhymes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Newnan, GA
- Parts Used:
- W10355051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
Baked on sauce
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from SEDRO WOOLLEY, WA
- Parts Used:
- W10856603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element failed
Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry D from Spring Valley, CA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element burned up
It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from WALDORF, MD
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wasn't preheating to temperature
Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).
Was this instruction helpful to you?
Thank you for voting!
Burner would randomly overheat on any setting (Bad Control Switch)
1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from PLAINFIELD, IN
- Parts Used:
- WP3148953
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The 8-inch burner only heated on high regardless of the temperature setting dialed in.
Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Philadelphia, PA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
electric coils would not stay flat as drip pans were incorrect fit
replaced drip pans with correct type
Was this instruction helpful to you?
Thank you for voting!
broken bottom drawer glide and missing rivet on drawer front panel
Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.
The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.
The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.
Was this instruction helpful to you?
Thank you for voting!