TEP315VQ0 Estate Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Louis from Grantsville, UT
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
terminal block back of range shorted and burned
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulette J. from Connell, WA
- Parts Used:
- WP9761346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner stopped working right.
Was able to unplug the old burner and plug the new one in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charlie from glenwood springs, CO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to temp.
Pulled the oven away from the wall, unplugged the oven. Unscrewed the back panel(2 screws)that covers the pigtail connection. Pulled the two wires that attached to the heating element. Inside the oven i removed the two screws holding the element in place and removed old element. Put the new element in place and returned screws. The two wires clipped effortlessly on the back, returned cover and screws and plugged the oven back in. Tested the oven and returned it to its position, reset the clock and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Ann Arbor, MI
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Left front 8 inch burner knob control stop regulating heat temprature.
I purchased a new infinite control switch 6". and replace the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Fishers, IN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element burned out
Went on line to see if the repair could be done by us. Watched repair video and from there on the repair went as smooth as it possibly could.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from kissimmee, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
top element was burnt out small burn hole in element
removed the screws that were on back side of oven securing panel that covered element terminals disconnected wiring to upper element then went in side oven area removing 4 upper mount screws that were holding upper element in place then removed old element and reinstalled new in same order was removed..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Elk River, MN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
I found a video on YouTube and watched it showing how to change the element - then I performed the repair based on the instructions and recommendations in the video. The video had some good recommendations and cautions that helped ensure a successful repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from lexington, GA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Chared Bake element
Unplug oven, open oven door wide,pull out racks, clean reside that old element left. I used power drill with phillips head bit,pulled out old element, and disconnected wires from clips. Connected new element to wires, and Presto.Turned bake element to 300 deg.and waited only to see it red and ready to cook.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from springville, AL
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Was Not Heating As It Should
Removed lower oven rack. Unplugged stove,removed 2 screws holding element in place,pulled element forward unplugged 2 wires. Reversed proc. To reinstall . Very simple. Parts were here in less than 24 hrs using standard shipping. Very good service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- L from Richardson, TX
- Parts Used:
- WP9761346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out coil
Simply slide out old coil by lifting cooktop pan; position new coil electirc elements in oven slots, slowly push in, then push coil tab into slot in pan for balance. No problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, NC
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element would not get red hot
Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Columbus, OH
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broiler didn't work
Removed original broiler element, and found it was open. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from Kaiser, MO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the heating element went out.
removed the two screws and unhooked the old heating element. I set the new element in place and attached the electrical leads and replaced the two screws and tested the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Wooster, OH
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove kept turning off
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elsie from Garner, NC
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new drip bowl and couldn't find ons that fit exactly but you had it
I removed the old one and put in the new one. Works great!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!