TGS326MS2 Estate Range - Instructions

Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.

Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.

The repair was VERY simple....2 screws, remove the broken handle, put now one in place, put back the 2 screws... done!! What I want other to know... is who with about 6 clicks from my home pc, I had the exact part i needed, ordered!!! I was dreading ordering this part so much because of all the hassle I have in getting to a website to order, and all the crap that goes with finding, the part....the ordering the part. This site was SOOOOO cool!! The handle had been broke for almost a year, and didn't want to replace it because of the usual hassle that goes with 'The Hunt". If I had know that Parts Select was so good about this, I would have had the new one installed 3 days after the original handle broke!! And shipping was SO FAST!! Have you people in my book marks for sure!! Thank you one and all!!!

had to replace a broken knob, plastic was broken on the inside fitting. Took all of 2 seconds to replace

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Turn off the breaker to the range. Unplug, too. Took off the 8 screws that hold the upper back panel on. Took a picture of the wire setup (this ain't my first rodeo). Removed two screws on the bottom of the old latch that hold it in place. Carefully removed the wire leads with needle-nose pliers because I didn't want to replace the wire leads. Reconnected the wires to the new latch, replaced the two screws to hold it onto the oven. Tested with the rocker switch on top and the oven door, both worked. Put the back panel on with the 8 screws.

Remove old knob and put new knob in. About 10 minutes total.

First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I turned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged igniter and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!

My son broke the drawer handle of our stove a few years ago. It took me a while to get this repaired because the first company we ordered from shipped the wrong product to us and did not allow us to do a return! The team at PartSelect had the correct product delivered in just a few days! Once I had the product on hand the repair was super easy. Thanks PartSelect for great service!! Nick, ShirtsThatGo

I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.

The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS897264 is the igniter and burner tube. Part number PS898618 is just the ignitor.