TGP310KW0 Estate Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Derrick from Marlton, NJ
- Parts Used:
- WPW10268483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner grate burnt out
Replaced grates
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CONSTANCE from LAWTON, OK
- Parts Used:
- WPW10202217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven handle
I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Ashland, WI
- Parts Used:
- WPW10202217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Scews from old one didn't fit the new one.
I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lore from lampasas, TX
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The Oven Did Not Come On.
It only took my husbend 6min to put in the new oven igniter. But it did not work, so I call your center and the rep there talk my husbend and told him how to unluck the key bord, and that worked. Thank you for all the help.
Was this instruction helpful to you?
Thank you for voting!
The old panel becamed worped & the finish was distressed.
Took the old one out and replaced it with the new one, fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dominic from Tucson, AZ
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old igniter glowed red but was too cold
Shut off gas and unplugged electrical cord. Removed grates; oven floor and flame spreader and then unbolted old igniter with nut driver. Removed shield in rear of over with Phillips screwdriver and unplugged igniter from power socket. Removed old igniter and replaced with new. Bolted new igniter into place with nut driver and plug into rear socket. Turned on gas and plugged in electric to test igniter; saw white glow and flame on in a minute. Replaced rear shield, flame spreader, oven floor and grates. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from Stryker, OH
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven igniter
ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Tomball, TX
- Parts Used:
- W10918546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Gas oven burner would not light
The igniter would glow but no gas was released to the burner. I was told that the igniter is bad because it is not getting hot enough to open the safety valve to release the gas to the burner. I turn the gas off and unplugged the oven. Opened the oven removed the racks then removed the two screws that hold the bottom plate of the oven. Now I can see the burner and the igniter. The igniter is held on to the burner with two screws. Unscrew then and unplugged the wires. Then replaced with new igniter. Replaced everything that I removed. Plugged oven back in and turned on gas. Then started oven, it takes 45 sec. for the igniter to get hot enough to release the gas and everything was working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Broadalbin, NY
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The oven wouldn't light.
Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Brookline, MA
- Parts Used:
- WPW10256908, WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When I originally purchased my stove, there was a large paper describing stove features. It was glued on and when I removed it, it left glue which I could not remove. I s hould have returned stove, but I didn't.
So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Plainfield, IL
- Parts Used:
- W10918546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven wasn't Heating
Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Dacula, GA
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Igniter was glowing but not enough to catch the catch the burner
Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Schaumburg, IL
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven will not heat up
most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martyn from Round Rock, TX
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner not lighting
To begin with,the symptoms were strange.....the burner would not ignite even though the igniter was glowing....but if you bumped anything in the broiler or pulled the drawer out and closed it abruptly,it would lite. This went on for a few weeks , until slamming and banging worked no more.(that was getting old anyway)I went ahead and ordered the igniter.It came fast and was very easy to replace.I went in from the oven,took out the racks and the bottom plate(2 screws), exposing the flame diverter that is just above the burner.(2 screws)You can access the igniter now ,and remove it.(2 screws),and unplug it.Reverse order to install the new one.I didnt unplug the range or turn off the power,because I screwed the igniter on first and then it was a matter of just plugging it in. Everything went back together and turned on the oven. Worked fine. Very easy to do,and no more banging around the broiler.Should have done it sooner.
Was this instruction helpful to you?
Thank you for voting!